Finishes & Seals

Sealing Sanded Floors – Varnishing and Oiling.

Once your wood floors have been sanded, stained and its gaps filled to perfection, we can get down to finalising the job and seal the bear wood-surface. Sealing the floor using proper varnishes or oils is crucial. We use professional high-quality products by industry leaders like Bona, Osmo and Junkers And because we care about how we leave our client’s environment, we use non-toxic, water borne varnishes with low odour and without any hazard to health. Finally, these products are environmentally friendly, so that’s our way of protecting Nature and contributing to a cleaner, better world for all of us.

The Products Range Used in Our Wood Floor Restoration and Installation Services.

During the years of experience we have established a range of professional wood floor installation and restoration products, which we recommend for use in our floor sanding and wood floor fitting services. Please find below more information and specifications about the products and equipment we utilise.

Bona Mega Varnish

Bona MegaBona Mega Varnish is a one-component, water-borne, 100% polyurethane finish for the surface treatment of timber floors in commercial and domestic areas subject to heavy wear. As cross-linking is achieved using oxygen in the air, Mega has the performance of a two-component finish without requiring a separate catalyst. It has all the advantages of a water-borne system, but still gives a deep, rich colouration similar to a solvent based finish.
Bona Mega comes in matt, satin and gloss finishes.

 

Bona Traffic Varnish

Bona Traffic Varnish is a two-component, water-borne, 100% polyurethane finish for the surface treatment of timber floors in commercial premises or wherever a high resistance to wear is required. It is also suitable for over-coating compatible factory pre-finished timber and cork floors. Traffic provides a clear, natural appearance, giving almost invisible protection when the IP (Matt) version is used. However, unlike oil, it offers a simple level of maintenance. Traffic is Bona’s most hard-wearing lacquer. Available in IP (Matt) or Silk-matt versions. Where there is a risk of side-bonding, Bona Prime Classic is recommended for the initial coat on bare wood. Bona Mega is a one-component, water-borne, 100% polyurethane finish for the surface treatment of timber floors in commercial and domestic areas subject to heavy wear. As cross-linking is achieved using oxygen in the air, Mega has the performance of a two-component finish without requiring a separate catalyst. It has all the advantages of a water-borne.
Bona Traffic comes in matt and satin finishes.

Bona Naturale Varnish

Bona Naturale Varnish comes as single and two-component varnish and it offers architects and designers a way of achieving a completely natural looking wooden floor with the durability and protection essential for commercial, retail or public spaces. Bona Naturale two-component gives a floor sealing protection comparable to Bona’s most wear-resistant finish. Water-borne Bona Naturale two-component should be combined with Bona Naturale Base. Slip resistance is also a feature of this finish, making it suitable for public areas, restaurants etc. Bona Naturale has also been tested for resistance to fire in accordance with EN 13501-1:2004.

 

Please note, Bona Naturale is not usually included as a standard finish in Woof Floor Experts quotations, but it will be recommended for certain floor works.
Bona Naturale comes only in Ultra-matt finish.

Lobadur WS Viva Varnish

Lobadur WS Viva is a one-component water-borne finish for parquet and wood floors with normal to heavy wearing. This floor finish has proven as highly recommended for pine floor boards and pine parquet flooring due to the characteristics it applies as a finish to that type of wood.
Lobadur WS Viva comes in matt and satin finishes.

 

Bona R850 Wood Floor Adhesive

Lobadur WS Viva Varnish R850 is an elastic single component silane-based adhesive for parquet floors fitting. The hardened adhesive is similar to conventional adhesives – able to withhold thrust during expansion, while the resistance sgainst shrinkage is very low. Tensions to the sub floor are therefore reduced. The use of a primer is in general not necessary. The adhesive hardens by a chemical reaction with moisture.

 

Bona Moisture Barier R580

Unique, single coat, fast setting, saline-based moisture barrier. Water and solvent-free, Bona R580 is designed to treat damp sub floors prior to the installation of wood flooring using Bona saline-based adhesives. Bona R580 can be used as a two-component system with water to gain an even shorter setting time.

Bona R580 is also compatible with Bona H650 levelling compound. Quartz sand must be broadcast into wet Bona R580 before the application of the levelling compound.
Bona R580 is fully compatible with Bona adhesives R850, R845 and R860 which can be applied directly to the moisture barrier.

 

Lobadur Wood Floor Resin Filler

Lobadur Resin Wood Floor Filler is a quality compound which is mixed with the dust collected during the finer floor sanding stages of the restoration process. The wood dust is mixed with the filler and applied into the gaps, cracks and scratches of the floor. The wood filler hardens quickly becoming a solid matter, which will require re-sanding of the floors again. In most cases the procedure has to repeated two or three times. An important step in wood floor gap filling, especially when working with pine floor boards is fixing the floors prior to the gap filling.

Please note, most companies will not guarantee the durability of the gap filling, as sometime the solidness of the floor depends on the sub-floor base.